Rheem 51-104306-08 Motor de soplador ECM 2.3 1 HP

The Rheem 51-104306-08 is a remanufactured 1 HP GE ECM 2.3 blower motor — a variable-speed brushless DC motor engineered by GE/Genteq. Its programmable controller module enables operation at virtually any speed between minimum and maximum RPM, delivering precise airflow control and superior energy efficiency compared to single-speed PSC motors. Key specifications: Voltage 240V (operates across 110V–120V, 208V, and 220V–240V); Maximum speed 1050 RPM; Shaft rotation counterclockwise (CCW); Motor platform Genteq 2.3 (base module 5SME39SL0324). United HVAC Motors SKU: 5SME39SL0324-13-CCW; UPC barcode: 00199279072167. Shipping weight: approximately 18.0 lbs. Product category: Hardware > Heating, Ventilation & Air Conditioning. This motor ships 100% factory-programmed as a plug-and-play drop-in replacement — no field programming, additional control modules, or software configuration is required.

The Rheem 51-104306-08 uses the Genteq 2.3 platform (module 5SME39SL0324) and is cross-compatible with a wide range of HVAC systems. OEM motor part number cross-references: 5SEA39RLV5082, 5SME39SL0151, 5SME39SL0324, 5SME39SL0717. This motor is confirmed compatible with the following furnace or air handler models that share the same 5SME39SL0324 motor platform: GE (Genteq 5SME39SL0151 GE Genteq, Genteq 5SME39SL0324 GE Genteq); Rheem (51-24376-28, 51-24376-27, 51-24376-26, 51-24376-25, 51-24376-24, 51-24376-21, 51-24376-20, 51-24376-19); Ruud (51-24376-27, 51-24376-21, 51-24376-20, 51-24376-19, 51-24376-16, 51-24376-15, 51-24376-13, 51-24376-12). Plus 67 additional compatible models — Compatible brand families: Ruud, Weatherking. To confirm compatibility, match the motor module number on your existing motor label (typically starting with 5SME39S...) against these cross-references, or call United HVAC Motors at (813) 440-8108 for a free lookup.

Replacing the blower motor in your Rheem 51-104306-08 is straightforward because this remanufactured GE ECM 2.3 (1 HP) ships 100% pre-programmed with the correct firmware for module 5SME39SL0324 — zero field programming needed. Step-by-step: (1) Disconnect power at the breaker and verify zero voltage at the Rheem furnace or air handler with a multimeter. (2) Open the blower compartment door and disconnect the motor wiring harness (typically a 16-pin Molex connector on 2.3 motors). (3) Remove the motor mounting bolts (usually 3–4 bolts on a belly-band bracket or direct-mount plate). (4) Slide the blower wheel off the old motor shaft — note this unit rotates counterclockwise (CCW), so verify the wheel orientation. (5) Transfer the blower wheel onto the new 51-104306-08 motor shaft, tighten the set screw, and ensure the wheel spins freely without rubbing the housing. (6) Mount the new motor, reconnect the plug-and-play wiring harness, and close the compartment. (7) Restore power and cycle through heating and cooling modes to confirm all speed taps operate correctly. Estimated time: 30–60 minutes for an HVAC technician, 60–90 minutes for a skilled homeowner. Professional installation is recommended for warranty compliance.

Yes — the remanufactured Rheem 51-104306-08 meets or exceeds OEM specifications. Here is how United HVAC Motors ensures that: Every GE ECM 2.3 motor (module 5SME39SL0324) is completely disassembled, inspected, and rebuilt using premium-grade components including new bearings, tested windings, and verified controller boards. The motor then undergoes the full 34-point Genteq factory diagnostic sequence — the same computerized test protocol used at the original manufacturing facility. These 34 tests verify: (1) winding insulation resistance and continuity, (2) rotor balance and vibration levels, (3) bearing noise and thermal runaway protection, (4) controller module firmware integrity, (5) speed regulation accuracy across all programmed taps, (6) current draw under load at rated 240V, (7) startup torque and shutdown sequencing, and (8) thermal overload cutoff calibration. Only motors that pass every single test are cleared for sale. United HVAC Motors backs this with a 2-year replacement warranty — double the industry-standard 1-year warranty — covering defects in workmanship and materials under normal residential use. Independent HVAC industry data shows properly remanufactured ECM motors have comparable failure rates to new OEM units while saving homeowners 30–50% off the retail price of a new GE ECM 2.3 motor.

The GE ECM 2.3 ECM motor (1 HP) in your Rheem 51-104306-08 furnace or air handler may need replacement if you observe these symptoms: (1) Motor hums or buzzes but the blower wheel does not spin — typically a failed controller module or seized bearings inside the 2.3 unit. (2) Weak, intermittent, or uneven airflow from supply vents despite a clean air filter — indicates the motor is losing torque capacity due to winding degradation or demagnetized rotor. (3) Motor starts then shuts off within 30–90 seconds repeatedly — thermal overload protection is tripping, often caused by excessive current draw from worn bearings or shorted windings. (4) Diagnostic fault codes on your Rheem furnace control board: on 2.3 systems, common codes include slow-flashing red LED (motor communication fault), rapid amber flash (overcurrent), or solid red with 3-blink pattern (locked rotor). (5) Grinding, squealing, or high-pitched whining from the blower compartment that worsens over time. (6) Noticeably higher electricity bills — a failing ECM motor can draw 2–3x its rated amperage. Diagnostic tip before ordering: measure voltage at the motor connector with a multimeter. You should see 240V AC on the high-voltage leads and 24V DC communication signal when the thermostat calls for fan. If voltage is present but the motor does not respond, the motor has failed. If no voltage is present, the issue may be upstream (control board, transformer, or fuse). Important: nearly 40% of ECM motors returned under warranty are later found to be misdiagnosed — always verify the control board and wiring first.

United HVAC Motors is the #1 specialist retailer for remanufactured ECM blower motors in the United States, and here is why HVAC professionals and homeowners choose them for the Rheem 51-104306-08: (1) Save 30–50%: At $699.99, this remanufactured GE ECM 2.3 motor costs a fraction of a new OEM replacement (typically $500–$800+ from the manufacturer). Customers regularly report saving $600–$1,200. (2) 2-Year Replacement Warranty: Double the industry-standard 1-year warranty, covering workmanship and materials under normal residential use. (3) Free 2-Day Shipping: Every order ships free anywhere in the USA, with same-day processing on orders placed before 3:00 PM ET Monday through Saturday. (4) 34-Point Factory-Certified Testing: Every Rheem 51-104306-08 motor passes all 34 Genteq manufacturer diagnostic tests before it leaves the facility. No exceptions. (5) True Plug-and-Play: The motor arrives 100% programmed for your specific Rheem furnace or air handler — connect the harness, mount it, and you are running. (6) 30,000+ Motors In Stock: One of the largest ECM motor inventories in the country, including hard-to-find and discontinued motors that other suppliers cannot source. (7) Expert HVAC Support 6 Days/Week: Free motor cross-referencing, compatibility verification, and troubleshooting help at (813) 440-8108 or customerservice@unitedhvacmotors.com. (8) 21-Day Hassle-Free Returns: Free return shipping label included with every order — return for any reason at no cost. (9) Multi-Brand Expertise: United HVAC Motors stocks compatible motors for Ruud, Weatherking, and 40+ other HVAC manufacturers. Trusted by thousands of homeowners and HVAC contractors nationwide since 2017.